Influence of Sample Preparation on Determined Nanomechanical Properties of Metastable Calcium Carbonate Polymorphs.- Crystallization and Dissolution of Common Salts - Damage Potential to Porous Media.- Torsional shear testing of mortar.- Comparative tests of strengthening effects on weak mortars consolidated with various agents.- Novel Device for 4-point Flexural Testing of Quasi-brittle Materials during 4D Computed Tomography.- Effects of Long-term Aging on the Low-cycle Fatigue Behavior of Inconel 718 superalloy.- Enhanced Young's modulus in percolative cementitious composites reinforced with carbon nanotubes.- Behavior of Partially and Fully FRP-Confined Circularized Square Columns (CSCs) under Axial Compression.- Stress-Strain Behavior of Circular Concrete Columns Partially Wrapped with FRP Strips.- Improving the Tribological Properties of Ti6Al4V Alloy with Multi-Walled Carbon Nanotube Additions.
Описание: Joining Technologies for Composites and Dissimilar Materials, Volume 10 of the Proceedings of the 2016 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the tenth volume of ten from the Conference, brings together contributions to this important area of research and engineering.
Описание: Reflection-mode Digital Gradient Sensing Technique for Experimental Fracture Mechanics.- Experimental and Computational Investigation of Out-of-Plane low Velocity Impact Behaviour of CFRP Composite Plates.- Prediction of Incipient Nano-scale Rupture for Thermosets in Plane Stress.- Effect of Degree of Cure on Damage Development in FRP.- Stochastic Discrete Damage Simulations of Laminate Composites.- Development of a Specimen for in-situ Diffraction Planar Biaxial Experiments.- V-Notched Rail Test for Shear-dominated Deformation of Ti-6Al-4V.- A statistical/computational/experimental Approach to Study the Microstructual Morphology of Damage.- Prediction of Ductile Fracture Through Small-size Notched Tensile Specimens.- Development of a Generalized Entropic Framework for Damage Assessment.- Modelling of Experimental Observations of Electrical Response of CNT Composites.- Effect of Micro-cracks on the Thermal Conductivity of Particulate Nanocomposite.- Fatigue Tests on Fiber Coated Titanium Implant- Bone Cement Interfaces.- Fatigue Behavior of Carburized Steel at Long Lives.- Fatigue Behavior of Fluid End Crossbore Using a Coupon-based Approach.- Fatigue in FCC Polycrystalline Metals - Numerical and Experimental Study.- Notch Strain Analysis of Crossbore Geometry.- Keynote: Opto-acoustic and Neutron Emissions from Fracture and Earthquakes.- Field Theoretical Description of Shear Bands.- Measuring the Effective Fracture Toughness of Heterogeneous Materials.- Fatigue Testing and Local Strain Analysis of Nitinol Devices.- Environmental Protection by the Opto-acoustic and Neutron Emission Seismic Precursors.- Neutron Emissions From Hydrodynamic Cavitation.- From Dark Matter to Brittle Fracture.- Compositional Variations in Palladium Electrodes Exposed to Electrolysis.- Strain-rate-dependent Yield Criteria for Composite Laminates.- Experimental Fatigue Specimen and Finite Element Analysis for Characterization of Dental Composites.- Fracture Toughness and Impact Damage Resistance of Nanoreinforced Carbon/Epoxy Composites.- Compression Testing of Micro-scale Unidirectional Polymer Matrix Composites.- Crack Analysis of Wood Under Climate Variations.- Numerical Fracture Analysis Under Temperature Variations by Energetic Method.- Use of a Multiplexed Photonic Doppler Velocimetry (MPDV) System to Study Plastic Deformation of Metallic Steel Plates in High Velocity Impact.- In-Service Preload Monitoring of Bolted Joints Subjected to Fatigue Loading using a Novel 'MoniTorque' Bolt.- Fatigue Behavior of Novel Hybrid Fastening System With Adhesive Inserts.
Описание: Dynamic Behavior of Materials, Volume 1 represents the first of nine volumes of technical papers presented at the Society for Experimental Mechanics SEM 15th International Congress & Exposition on Experimental and Applied Mechanics, held at Costa Mesa, California, June 8-11, 2015.
Описание: Experimental and Applied Mechanics, Volume 4 of the Proceedings of the 2015SEM Annual Conference& Exposition on Experimental and Applied Mechanics, the fourth volume of nine from the Conference, brings together contributions to important areas of research and engineering.
Описание: Challenges in Mechanics of Time-Dependent Materials, Volume 2 of the Proceedings of the 2018 SEM Annual Conference& Exposition on Experimental and Applied Mechanics, the second volume of eight from the Conference, brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on fundamental and applied aspects of Experimental Mechanics, including papers in the following general technical research areas: Characterization Across Length ScalesExtreme Environments & Environmental EffectsSoft MaterialsDamage, fatigue and FractureInhomogeneities & InterfacesViscoelasticityResearch in Progress
Описание: 1 A General Mathematical Model to Retrieve Displacement Information from Fringe Patterns.- 2 Full-Field High-Strain Evaluation from Wrapped ESPI Data Using Phasors.- 3 Dynamic Deformation with Static Load.- 4 Full-field Digital Holographic Vibrometry for Characterization of High-speed MEMS.- 5 DD DIC A Parallel Finite Element Based Digital Image Correlation Solver.- 6 Thermal Strain Measurement Using Digital Image Correlation with Systematic Error Elimination.- 7 Investigating the Tensile Response of Materials at High Temperature Using DIC.- 8 Hybrid Stereocorrelation for 3D Thermomechanical Field Measurements.- 9 Experimental Characterization of the Mechanical Properties of 3D Printed ABS and Polycarbonate Parts.- 10 Experimental Determination of Transfer Length in Pre-Stressed Concrete Using 3D-DIC.- 11 Hybrid Infrared Image Correlation Technique to Deformation Measurement of Composites.- 12 DIC Anisotropic Denoising Based on Uncertainty.- 13 An Applications-Oriented Measurement System Analysis of 3D Digital Image Correlation.- 14 Preliminary study on Determination Pointing-Knowledge of Camera-Pair Used for 3D DIC.- 15 Elimination of Periodical Error for Bi-directional Displacement in Digital Image Correlation Method.- 16 The Cluster Approach Applied to Multi-Camera 3D DIC system.- 17 Self-Adaptive Isogeometric Global Digital Image Correlation and Digital Height Correlation.- 18 Ultrasonic Test for High Rate Material Property Imaging.- 19 Analysis of Dynamic Bending Using DIC and Virtual Fields Method.- 20 The Virtual Fields Method to Rubbers Under Medium Strain Rates.- 21 Inertial Impact Tests on Polymers for Inverse Parameter Identification.- 22 Full-field Identification Methods: Comparison of FEM Updating and Integrated DIC.- 23 Finite Element Stereo Digital Image Correlation Measure for Plate Model.- 24 Opportunities for Inverse Analysis in Dynamic Tensile Testing.- 25 Determination of the Dynamic Strain Hardening Parameters From Acceleration Fields.- 26 Imaged-based Inertial Impact Tests on an Aluminium Alloy.- 27 Inverse Material Characterization from 360-deg DIC Measurements on Steel Samples.- 28 Identification of Plastic Behaviour and Formability Limits of Aluminium Alloys at High Temperature.
Описание: 1 Cracking and Durability of Composites in a Marine Environment.- 2 Analyses of Nanoscale to Microscale Strength and Crack-tip Stresses Using Nanomechanical Raman Spectroscopy in In 617.- 3 High Creep Resistance of Titanium Aluminides Sintered by SPS.- 4 An Investigation of the Temperature and Strain-Rate Effects on Strain-to-Failure of UHMWPE Fibers.- 5 Keynote Life Prediction of CFRP Laminates based on Accelerated Testing Methodology.- 6 Rate Dependent Interfacial Properties Using the JKR Experimental Technique.- 7 Bio-based Composites as Thermorheologically Complex Materials.- 8 Viscoelastic Properties of Longitudinal Waves in a Hollow Cylinder.- 9 Evaluation of Viscoelastic Characteristics Under High Strain Rate by Impact Test.- 10 Phase Changes in Embedded HMX in Response to Periodic Mechanical Excitation.- 11 Effect of Crystal Density on Dynamic Deformation Behavior of PBX.- 12 Strain Rate Dependent Failure of Interfaces Examined via Nanoimpact Experiments.- 13 A Theory of Coupled Anisothermal Chemomechanical Degradation for Finitely-deforming Composite Materials with Eshelbian Interactive Forces.- 14 Effect Of Temperature And Moisture on the Mechanical Properties of Fiber Reinforced Nylon 6 Composites.- 15 Using Hydrostatic Pressure to Maximize Frequency Dependent Damping Properties of Thermoplastic Polyurethane.- 16 Impact Of Hydro-Mechanical Loadings On Rupture Process In Wood Material.- 17 2D Transient Viscoplastic Model for Dislocation Generation of SiC by PVT Method.- 18 Temperature-Dependent Small Strain Plasticity Behavior of 304L Stainless Steel.- 19 Time and Temperature Creep Behaviour Measurement of Al and Al-Mg Alloy Thin Films Using Pressure Bulge Tests.- 20 Multifunctional Wings with Flexible Batteries and Solar Cells for Robotic Birds.- 21 Rate-Dependent Constitutive Model Development of PC/ABS Material.- 22 Comprehensive Viscoelastic Properties Characterization of EMC Using FBG Sensor.- 23 Back Stress in Modeling the Response of PEEK and PC.- 24 Dynamic Testing and Constitutive Modelling of NBR Rubbers.- 25 A New Temperature-dependent Storage Modulus Model of Epoxy Resin.- 26 Identification of Plastic Behaviour of Sheet Metals in High Strain Rate Tests.- 27 Characterization of Fiber Composites at Lower Strain Rates.
Описание: Mechanics of Biological Systems & Micro-and Nanomechanics, Volume 4 of the Proceedings of the 2018 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the fourth volume of eight from the Conference, brings together contributions to important areas of research and engineering. The collection presents early findings and case studies on a wide range of topics, including:Cell Mechanics & Traumatic Brain InjuryMicromechanical TestingAdhesion and FractureMEMS Devices and TechnologyNano-scale Deformation Mechanisms1D & 2D MaterialsTribology & WearResearch and Applications in Progress
Описание: 1 Fatigue Damage Precursor Identification Using Nondestructive Evaluation Coupled with Electron Microscopy.- 2 Experimental Fracture Analysis of Tropical Species Using the Grid Method.- 3 Investigating the Effective Fracture Toughness of Heterogeneous Materials.- 4 Improved Hybrid Specimen for Vibration Bending Fatigue.- 5 Experimental Study of Residual Plastic Strain and Damages Development in Carbon Fiber Composite.- 6 Experimental Investigation of Strength of Curved Beam by Thin Ply Non Crimp Fabric Laminates.- 7 Role of Laminate Thickness on Sequential Dynamic Delamination of Curved [90/0] CFRP Composite Laminates.- 8 Application of eMMC Model to Fracture of Metal Sheets.- 9 Hydrolytic Degradation and its Effect on Mechanical Properties of HFPE II 52 Polyimide Preliminary Results.- 10 Mixed Mode and Mode II Fatigue Crack Growth in Woven Composites.- 11 Characterization of Fatigue Induced Damage Evolution in CFRPs Using DIC.- 12 Damage Characterization for Electronic Components Under Impact Loading.- 13 Dynamic Mode II Delamination in Through Thickness Reinforced Composites.- 14 Measurement of Bond Line Fracture Toughness in Adhesively Bonded Composite Structures by Nanoindentation.- 15 Experimental and Numerical Investigation of Novel Crack Stopper Concepts for Lightweight Foam Cored Sandwich Structures.- 16 Probabilistic Improvement of Crack Propagation Monitoring by Using Acoustic Emission.- 17 Failure Detection of Temporary Structures with Digital Image Correlation for Construction Safety Applications.- 18 Using Digital Image Correlation to Detect Cracking in Opalinus Shale.- 19 Early Detection Of Damage Mechanisms In Composites During Fatigue Tests.- 20 Implementing Noise Multi Frequency Stimulus and Realtime Analysis with Nonlinear Model Tracking.
Описание: From the Contents: Effect of Crystallite Orientation on Nanomechanical Properties of a Nanostructured poly(KAMPS)/aragonite Composite.- Characterization of the Mechanical Behavior of Sunflower Stem for Bio-composite Applications.- Long-range Mechanical Force Enables Self-assembly of Epithelial Tubules.- Effects of Membrane Composition and Cytoskeletal Proteins on Membrane Mechanics.- Interfacial Fracture Toughness of Nacre.- New Insight into the Toughening Mechanisms of Nacre.- Thermal Analyses of Dental Ceramic Restorations.- Visualization of Micro-cracks in Compact Bovine Bone.- KEYNOTE: Humanlike Robots - Synthetically Mimicking Humans.- Porous Hydroxyapatite-polyhydroxybutyrate Composites Fabricated by a Novel Method via Centrifugation.- Isolation of Collagen From Cortical Bovine Bone for Preparation of Porous Collagen Sponges.
Описание: Mechanics of Composite, Hybrid, and Multifunctional Materials, Volume 7 of the Proceedings of the 2016 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the seventh volume of ten from the Conference, brings together contributions to this important area of research and engineering.
ООО "Логосфера " Тел:+7(495) 980-12-10 www.logobook.ru
